| 1. |
- Andersson, Mattias, et al.
(författare)
-
Intrinsic and extrinsic influences on the temperature dependence of mobility in conjugated polymers
- 2008
-
Ingår i: Organic electronics. - : Elsevier. - 1566-1199 .- 1878-5530. ; 9:5, s. 569-574
-
Tidskriftsartikel (refereegranskat)abstract
- The temperature dependence of charge carrier mobility in conjugated polymers and their blends with fullerenes is investigated with different electrical methods, through field effect transistor (FET), space charge limited current (SCLC) and charge extraction (CELIV) measurements. Simple models, such as the Gaussian disorder model (GDM), are shown to accurately predict the temperature behavior, and a good correlation between the different measurement methods is obtained. Inconsistent charge carrier concentrations in the modeling are explained through intrinsic non-equilibrium effects, and are responsible for the limited applicability of existing numerical models. A severe extrinsic influence from water in FETs with a hydrophilic insulator interface is also demonstrated. The presence of water leads to a significant overestimate of the disorder in the materials from measurements close to room temperature and erratic behavior in the 150-350 K range. To circumvent this problem it is shown to be necessary to measure under ultra high vacuum (UHV) conditions. © 2008 Elsevier B.V. All rights reserved.
|
|
| 2. |
- Andersson, Mattias, et al.
(författare)
-
Mixed C60/C70 based fullerene acceptors in polymer bulk-heterojunction solar cells
- 2012
-
Ingår i: Organic Electronics: physics, materials, applications. - : Elsevier BV. - 1566-1199 .- 1878-5530. ; 13:12, s. 2856-2864
-
Tidskriftsartikel (refereegranskat)abstract
- Different mixtures of identically substituted C60 and C70 based fullerens have been used as acceptors in three polymer: fullerene systems that strongly express various performance limiting aspects of bulk heterojunction solar cells. Results are correlated with, and discussed in terms of e.g. morphology, charge separation, and charge transport. In these systems, there appears to be no relevant differences in either mobility or energy level positions between the identically substituted C60 and C70 based fullerenes tested. Examples of how fullerene mixtures influence the nano-morphology of the active layer are given. An upper limit to the open circuit voltage that can be obtained with fullerenes is also suggested.
|
|
| 3. |
|
|
| 4. |
- Barrau, Sophie, et al.
(författare)
-
Nanomorphology of Bulk Heterojunction Organic Solar Cells in 2D and 3D Correlated to Photovoltaic Performance
- 2009
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 42:13, s. 4646-4650
-
Tidskriftsartikel (refereegranskat)abstract
- Control of the nanoscale morphology of the donor-acceptor material blends inorganic solar Cells is critical for optimizing the photovoltaic performances. The influence of intrinsic (acceptor materials) and extrinsic (donor:acceptor weight ratio, substrate, solvent) parameters was investigated, by atomic force microscopy (AFM) and electron tomography (ET), on the nanoscale phase separation of blends of a low-band-gap alternating polyfluorene copolymers (APFO-Green9) with [6,6]-phenyl-C-71-butyric acid methyl ester ([70]PCBM). The photovoltaic performances display an optimal efficiency for the device elaborated with a 1:3 APFO-Green polymer:[70][PCBM weight ratio and spin-coated from chloroform solution. The associated active layer morphology presents small phase-separated domains which is a good balance between as a large interfacial donor-acceptor area and Continuous paths of the donor and acceptor phases to the electrodes.
|
|
| 5. |
- Bergqvist, Jonas, et al.
(författare)
-
Asymmetric photocurrent extraction in semitransparent laminated flexible organic solar cells
- 2018
-
Ingår i: npj Flexible Electronics. - : Springer Science and Business Media LLC. - 2397-4621. ; 2:1
-
Tidskriftsartikel (refereegranskat)abstract
- Scalable production methods and low-cost materials with low embodied energy are key to success for organic solar cells. PEDOT(PSS) electrodes meet these criteria and allow for low-cost and all solution-processed solar cells. However, such devices are prone to shunting. In this work we introduce a roll-to-roll lamination method to construct semitransparent solar cells with a PEDOT(PSS) anode and an polyethyleneimine (PEI) modified PEDOT(PSS) cathode. We use the polymer:PCBM active layer coated on the electrodes as the lamination adhesive. Our lamination method efficiently eliminates any shunting. Extended exposure to ambient degrades the laminated devices, which manifests in a significantly reduced photocurrent extraction when the device is illuminated through the anode, despite the fact that the PEDOT(PSS) electrodes are optically equivalent. We show that degradation-induced electron traps lead to increased trap-assisted recombination at the anode side of the device. By limiting the exposure time to ambient during production, degradation is significantly reduced. We show that lamination using the active layer as the adhesive can result in device performance equal to that of conventional sequential coating.
|
|
| 6. |
- Bergqvist, J., et al.
(författare)
-
Sub-glass transition annealing enhances polymer solar cell performance
- 2014
-
Ingår i: Journal of Materials Chemistry A. - 2050-7488 .- 2050-7496. ; 2:17, s. 6146-6152
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal annealing of non-crystalline polymer:fullerene blends typically results in a drastic decrease in solar cell performance. In particular aggressive annealing above the glass transition temperature results in a detrimental coarsening of the blend nanostructure. We demonstrate that mild annealing below the glass transition temperature is a viable avenue to control the nanostructure of a non-crystalline thiophene–quinoxaline copolymer:fullerene blend. Direct imaging methods indicate that coarsening of the blend nanostructure can be avoided. However, a combination of absorption and luminescence spectroscopy reveals that local changes in the polymer conformation as well as limited fullerene aggregation are permitted to occur. As a result, we are able to optimise the solar cell performance evenly across different positions of the coated area, which is a necessary criterion for large-scale, high throughput production.
|
|
| 7. |
- Cai, Tianqi, et al.
(författare)
-
Low bandgap polymers synthesized by FeCl(3) oxidative polymerization
- 2010
-
Ingår i: Solar Energy Materials and Solar Cells. - : Elsevier BV. - 0927-0248. ; 94:7, s. 1275-1281
-
Tidskriftsartikel (refereegranskat)abstract
- Four low bandgap polymers, combining an alkyl thiophene donor with benzo[c][1,2,5]thiadiazole, 2,3-diphenylquinoxaline, 2,3-diphenylthieno[3,4-b]pyrazine and 6,7-diphenyl-[1,2,5]thiadiazolo[3,4-g] quinoxaline acceptors in a donor-acceptor-donor architecture, were synthesized via FeCl3 oxidative polymerization. The molecular weights of the polymers were improved by introducing o-dichlor-obenzene (ODCB) as the reaction solvent instead of the commonly used solvent, chloroform. The photophysical, electrochemical and photovoltaic properties of the resulting polymers were investigated and compared. The optical bandgaps of the polymers vary between 1.0 and 1.9 eV, which is promising for solar cells. The devices spin-coated from an ODCB solution of P1DB:[70]PCBM showed a power conversion efficiency of 1.08% with an open-circuit voltage of 0.91 V and a short-circuit current density of 3.36 mA cm(-2) under irradiation from an AM1.5G solar simulator (100 mW cm(-2)). (C) 2010 Elsevier B.V. All rights reserved.
|
|
| 8. |
- Chen, Miaoxiang, 1962-, et al.
(författare)
-
High carrier mobility in low band gap polymer-based field-effect transistors
- 2005
-
Ingår i: Applied Physics Letters. - : AIP Publishing. - 0003-6951 .- 1077-3118. ; 87:25, s. 252105-1-252105-3
-
Tidskriftsartikel (refereegranskat)abstract
- A conjugated polymer with a low band gap of 1.21 eV, i.e., absorbing infrared light, is demonstrated as active material in field-effect transistors (FETs). The material consists of alternating fluorene units and low band gap segments with electron donor-acceptor-donor units composed of two electron-donating thiophene rings attached on both sides of a thiadiazolo-quinoxaline electron-acceptor group. The polymer is solution-processable and air-stable; the resulting FETs exhibit typical p-channel characteristics and field-effect mobility of 0.03 cm2 V−1 s−1.
|
|
| 9. |
- Diaz de Zerio Mendaza, Amaia, 1986, et al.
(författare)
-
Neat C60:C70 buckminsterfullerene mixtures enhance polymer solar cell performance
- 2014
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 2:35, s. 14354-14359
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate that bulk-heterojunction blends based on neat, unsubstituted buckminsterfullerenes (C60, C70) and a thiophene–quinoxaline copolymer (TQ1) can be readily processed from solution. Atomic force and transmission electron microscopy as well as photoluminescence spectroscopy reveal that thin films with a fine-grained nanostructure can be spin-coated, which display a good photovoltaic performance. Replacement of substituted fullerenes with C60 or C70 only results in a small drop in open-circuit voltage from 0.9 V to about 0.8 V. Thus, a power conversion efficiency of up to 2.9% can be maintained if C70 is used as the acceptor material. Further improvement in photovoltaic performance to 3.6% is achieved, accompanied by a high internal quantum efficiency of 75%, if a 1 : 1 C60:C70 mixture is used as the acceptor material, due to its improved solubility in ortho-dichlorobenzene.
|
|
| 10. |
- Gadisa, Abay, et al.
(författare)
-
Improvements of fill factor in solar cells based on blends of polyfluorene copolymers as electron donors
- 2007
-
Ingår i: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 515:5, s. 3126-3131
-
Tidskriftsartikel (refereegranskat)abstract
- The photovoltaic characteristics of solar cells based on alternating polyfluorene copolymers, poly(2,7-(9,9-dioctyl-fluorene)-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)) (APFO-3), and poly(2,7-(9,9-didodecyl-fluorene)-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)) (APFO-4), blended with an electron acceptor fullerene molecule [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), have been investigated and compared. The two copolymers have the same aromatic backbone structure but differ by the length of their alkyl side chain. The overall photovoltaic performance of the solar cells is comparable irrespective of the copolymer used in the active layer. However, the fill factor (FF) values of the devices are strongly affected by the copolymer type. Higher FF values were realized in solar cells with APFO-4 (with longer alkyl side chain)/PCBM bulk heterojunction active layer. On the other hand, devices with blends of APFO-3/APFO-4/PCBM were found to render fill factor values that are intermediate between the values obtained in solar cells with APFO-3/PCBM and APFO-4/PCBM active film. Upon using APFO-3/APFO-4 blends as electron donors, the cell efficiency can be enhanced by about 16% as compared to cells with either APFO-3 or APFO-4. The transport of holes in each polymer obeys the model of hopping transport in disordered media. However, the degree of energetic barrier against hopping was found to be larger in APFO-3. The tuning of the photovoltaic parameters will be discussed based on studies of hole transport in the pure polymer films, and morphology of blend layers. The effect of bipolar transport in PCBM will also be discussed.
|
|
